I'll need to put in a new circuit for my wife's new toy, but I can't find any information on the amp load for the the 3520b (the box won't be opened until Christmas). I downloaded the manual from PM but even that doesn't say.
With a 2h...
[Tags: No tags defined yet] - Be the first to Tag this threadAdd TagsCancel
*Note: Tags must be comma (,) seperated. For example: boardtracker, forum search, search engine
clear out a space by the wall and slide the lathe in place
put Dad's old rolling tool chests in front
pile on various boxes from recent purchases, other junk on the sides
talk about how you feel better 'cause you got lots of rearranging...
[Tags: No tags defined yet] - Be the first to Tag this threadAdd TagsCancel
*Note: Tags must be comma (,) seperated. For example: boardtracker, forum search, search engine
My wife's 3520b Christmas present has arrived far earlier than I expected. Now I have to figure out where to hide it until Christmas. It's not like I can stick it on the top shelf of the closet.
Seriously, though, this is my first...
[Tags: No tags defined yet] - Be the first to Tag this threadAdd TagsCancel
*Note: Tags must be comma (,) seperated. For example: boardtracker, forum search, search engine
As you may recall, I'm getting a 3520B for my wife's Christmas present. Woodcraft is participating in Powermatic's 15% off sale, so the price was down to $2900.
With Bing cash-back and avoiding sales tax, I would be able to get the...
[Tags: No tags defined yet] - Be the first to Tag this threadAdd TagsCancel
*Note: Tags must be comma (,) seperated. For example: boardtracker, forum search, search engine
My wife works on an ancient Craftsman lathe we inherited from my dad. Spindle work only. But I've gotten interested in doing bowls and with WC's upcoming sale on Powermatic, I'm planning to "surprise" her for Christmas with ...
[Tags: No tags defined yet] - Be the first to Tag this threadAdd TagsCancel
*Note: Tags must be comma (,) seperated. For example: boardtracker, forum search, search engine
Bare hands are not recommended ...
...
[Tags: No tags defined yet] - Be the first to Tag this threadAdd TagsCancel
*Note: Tags must be comma (,) seperated. For example: boardtracker, forum search, search engine
This is some very old wood and I'm curious what it is. When cut it has a very strong pine odor, but it's heavier and darker than any pine I've seen. It may not come through on the picture, but it's got a reddish tone rather than yello...
[Tags: No tags defined yet] - Be the first to Tag this threadAdd TagsCancel
*Note: Tags must be comma (,) seperated. For example: boardtracker, forum search, search engine
Just got a brand-new Jet bench grinder. I turned it on and it started vibrating wildly. Before I could flip the switch back off, the wheel cracked and jammed in the guard, stopping the motor cold. I also heard something go whizzing r...
[Tags: No tags defined yet] - Be the first to Tag this threadAdd TagsCancel
*Note: Tags must be comma (,) seperated. For example: boardtracker, forum search, search engine
I've been eyeing a drum sander for a while, but really couldn't justify the money for something I wasn't sure I'd use a lot. But when I got a chance to pick up this lightly-used one for $225, I couldn't say no. Per official gloat rules...
[Tags: No tags defined yet] - Be the first to Tag this threadAdd TagsCancel
*Note: Tags must be comma (,) seperated. For example: boardtracker, forum search, search engine
Yesterday, I wasn’t paying attention and tried to tilt my tablesaw blade over to 45 degrees. I encountered some resistance and, thinking that the previously flawless tilt mechanism was sticking a bit, forced it. The real cause was...
[Tags: No tags defined yet] - Be the first to Tag this threadAdd TagsCancel
*Note: Tags must be comma (,) seperated. For example: boardtracker, forum search, search engine
I have a chance to pick up one of these sanders, barely used, for a pretty good price. It's one of the pre-Jet models. The owner doesn't have the manual and really knows nothing about it.
Does anyone know if the old Performax vers...
[Tags: No tags defined yet] - Be the first to Tag this threadAdd TagsCancel
*Note: Tags must be comma (,) seperated. For example: boardtracker, forum search, search engine
I'm about to splurge on a Wolverine sharpening system for my wife. However, I'm a little confused on what grinding wheels to get. Hartville has wheels listed as "I" and "K" hardness. I understand what that means, but...
[Tags: No tags defined yet] - Be the first to Tag this threadAdd TagsCancel
*Note: Tags must be comma (,) seperated. For example: boardtracker, forum search, search engine
Anyone know a source for a good, precision measuring tape? I was getting frustrated with some measuring errors, so I lined up my 4 measuring tapes. None of them agreed with each other, with a variation of 3/16" at 8'
Ideally,...
[Tags: No tags defined yet] - Be the first to Tag this threadAdd TagsCancel
*Note: Tags must be comma (,) seperated. For example: boardtracker, forum search, search engine
N/A
N/A
N/A
N/A
Last 13 (of 13) threads initiated by <Not found> on 
