I know there's a lot of threads out there on this subject and everyone I've read isn't really convincing me if I should or shouldn't do it.....some people say there will be no problem with valve to piston clearance, and then some say that they will make c...
[Tags: clearance, h22, non-vtec-h23, pistons, prelude, type-s, valve, vtec] - Add more TagsAdd TagsCancel
*Note: Tags must be comma (,) seperated. For example: boardtracker, forum search, search engine
I know there's a lot of threads out there on this subject and everyone I've read isn't really convincing me if I should or shouldn't do it.....some people say there will be no problem with valve to piston clearance, and then some say that they will mak...
[Tags: clearance, h22, non-vtec-h23, pistons, prelude, type-s, valve, vtec] - Add more TagsAdd TagsCancel
*Note: Tags must be comma (,) seperated. For example: boardtracker, forum search, search engine
So I'm getting rid of left-overs and D15B7 engine parts. For new guys to know, all D-series engine parts are pretty much interchangeable, if you have a question just ask.
EVERYTHING is best offer need most of this stuff gone
-ECU original d15b7 ecu US...
[Tags: block, cam, camshaft, crank, crankshaft, head, header, intake, manifold, part, part-out, piston, rocker-arm, shaft, valve] - Add more TagsAdd TagsCancel
*Note: Tags must be comma (,) seperated. For example: boardtracker, forum search, search engine
so i was thinking of adding a performance cam to my d15b swap...along with a cat back exhaust. what kind of hp gains am i lookin at with the 2?...
[Tags: cam, d15b, gains, valve] - Add more TagsAdd TagsCancel
*Note: Tags must be comma (,) seperated. For example: boardtracker, forum search, search engine
just traded my banshee for a 93 hatch with a b16. when i got it i could hear a tick from the head, thought it would only need a simple valve adjustment but i have done them twice now and the noise is still there. could it be the lost motion assemblys? als...
[Tags: b16, head, lma, valve] - Add more TagsAdd TagsCancel
*Note: Tags must be comma (,) seperated. For example: boardtracker, forum search, search engine
I need to replace my F22B valve guide seals and have never seen the type seal before. How do you get the seals and caps off? Is the a special tool that MUST be used to press the new caps back on? Any help is appreciated....
[Tags: f22b, guide-seals, valve] - Add more TagsAdd TagsCancel
*Note: Tags must be comma (,) seperated. For example: boardtracker, forum search, search engine
This bov came with the turbonetics kit I bought a few months ago , I used it for about 500 miles and swapped it out , due to I didnt care for the sound it produced, you know the waaa pish pish pish pish pish pisssshhhhhh ...(lmao)
60 shipped or be...
[Tags: turbo, off, bov, blow, valve] - Add more TagsAdd TagsCancel
*Note: Tags must be comma (,) seperated. For example: boardtracker, forum search, search engine
ok the car i am geting (86 Accord LX) has low compression 70-75PSI on all 4 cyl's
what could cause this?
also the car was tested with out a carb on
also the car needs valve guides ...
[Tags: accord, compresion, guides, low, valve] - Add more TagsAdd TagsCancel
*Note: Tags must be comma (,) seperated. For example: boardtracker, forum search, search engine
as far as my knowlege a 3 angle valve job is good to do because it helps your valves seat in better and tighter but people keep telling me its a wast of money,.. is this ture? ...
[Tags: head, port, valve] - Add more TagsAdd TagsCancel
*Note: Tags must be comma (,) seperated. For example: boardtracker, forum search, search engine
Search matches - Showing results 1 - 14 of 14
